nat-traverse - Online in the Cloud

PROGRAM:

NAME

nat-traverse - Use of UDP to traverse NAT gateways

SYNOPSIS

To create a simple text-only tunnel, use the commands

user@left $ nat-traverse 40000:natgw-of-right:40001
user@right $ nat-traverse 40001:natgw-of-left:40000

where 40000 is an unused UDP port on "left" and 40001 is an unused port on "right". See
"EXAMPLES" for more.

VERSION

This document describes nat-traverse v0.5.

DESCRIPTION

nat-traverse establishes connections between nodes which are behind NAT gateways, i.e.
hosts which do not have public IP addresses. Additionally, you can setup a small VPN by
using pppd on top of nat-traverse (see "EXAMPLES"). nat-traverse does not need an
external server on the Internet, and it isn't necessary to reconfigure the involved NAT
gateways, either. nat-traverse works out-of-the-box.

See "TECHNIQUE" for how this is achieved.

Limitation: nat-traverse does not work with gateways which change the port numbers. This
is a fundamental problem of nat-traverse's design, as the changed port numbers are (in
general) not predictable.

OPTIONS

"local_port:peer:remote_port" (required)
Sets the local port to use and the remote address to connect to.

Note that you have to give the IP address or hostname of the NAT gateway of the host
you want to connect to, as the target host doesn't have a public IP address.

"--cmd="pppd...""
Runs the specified command after establishing the connection.

The command will be run with its STDIN and STDOUT bound to the socket, i.e.
everything the command writes to STDOUT will be forwarded to the peer.

If no command is specified, nat-traverse will relay input from STDIN to the peer and
vice versa, i.e. nat-traverse degrades to netcat.

"--window=10"
Sets the number of initial garbage packets to send. The default, 10, should work with
most firewalls.

"--timeout=10"
Sets the maximum number of seconds to wait for an acknowledgement by the peer.

"--quit-after-connect"
Quits nat-traverse after the tunnel has been established successfully.

nat-traverse returns a non-0 statuscode to indicate that it wasn't able to establish
the tunnel.

"--quit-after-connect" is useful if you want another program to use the tunnel. For
example, you could configure OpenVPN to use the the same ports as nat-traverse -- thus
OpenVPN would be able to cross NAT gateways.

"--version", "--help"

TECHNIQUE

nat-traverse establishes connections between hosts behind NAT gateways without need for
reconfiguration of the involved NAT gateways.

1. Firstly, nat-traverse on host "left" sends garbage UDP packets to the NAT gateway of
"right". These packets are, of course, discarded by the firewall.

2. Then "right"'s nat-traverse sends garbage UDP packets to the NAT gateway of "left".
These packets are not discarded, as "left"'s NAT gateway thinks these packets are
replies to the packets sent in step 1!

3. "left"'s nat-traverse continues to send garbage packets to "right"'s NAT gateway.
These packets are now not dropped either, as the NAT gateway thinks the packets are
replies to the packets sent in step 2.

4. Finally, both hosts send an acknowledgement packet to signal readiness. When these
packets are received, the connection is established and nat-traverse can either relay
STDIN/STDOUT to the socket or execute a program.

EXAMPLES

Setup of a small VPN with PPP
It's easy to setup a VPN (Virtual Private Network) by using the Point-to-Point Protocol
Daemon, "pppd":

root@left # nat-traverse \
--cmd="pppd updetach noauth passive notty \
ipparam vpn 10.0.0.1:10.0.0.2"
40000:natgw-of-right:40001
root@right # nat-traverse \
--cmd="pppd nodetach notty noauth"
40001:natgw-of-left:40000

"pppd" creates a new interface, typically "ppp0". Using this interface, you can ping
10.0.0.1 or 10.0.0.2. As you can see, "pppd" upgrades the data-only tunnel nat-traverse
provides to a full IP tunnel. Thus you can establish reliable TCP connections over the
tunnel, even though the tunnel uses UDP! Furthermore, you could even add IPv6 addresses
to "ppp0" by running "ip -6 addr add..."!

Note though that although this VPN is arguably a private network, it is not secured in any
way. You may want to use SSH to encrypt the connection.

Port Forwarding with netcat
You can use "netcat" to forward one of your local UDP or TCP ports to an arbitrary UDP or
TCP port of the remote host, similar to "ssh -L" or "ssh -R":

user@left $ nat-traverse 10001:natgw-of-right:10002 \
--cmd="nc -vl 20000"
user@right $ nat-traverse 10002:natgw-of-left:10001 \
--cmd="nc -v localhost 22"

As soon as the tunnel is established (using UDP ports 10001 and 10002), "left"'s TCP port
20000 is forwarded to "right"'s SSH Daemon (TCP port 22):

user@some-other-host $ ssh -p 20000 user@left
# Will connect to right's SSH daemon!

But do note that you lose the reliability of TCP in this example, as the actual data is
transported via UDP; so this is only a toy example. If you want reliable streams, use PPP
on top of nat-traverse, as described above.

Setup of a VPN with OpenVPN
You can use <OpenVPN> over nat-traverse if you want to have a secure VPN.

Using OpenVPN over nat-traverse requires only one change to OpenVPN's configuration file,
presuming that you don't want to use OpenVPN's multi-client mode: You have to adjust the
"code" and "lport" options accordingly, for example:

# Options to add to left's and right's OpenVPN config:
port 60001
lport 60001

# Command to execute on left resp. right:
root@left # until \
nat-traverse --quit-after-connect 60001:right:60001 \
do \
sleep 5 \
done; \
openvpn [...]
root@right # until \
nat-traverse --quit-after-connect 60001:left:60001 \
do \
sleep 5 \
done; \
openvpn [...]<!--

The "until" loop ensures that OpenVPN will not be started before nat-traverse was able to
establish the connection. Michael Kugele ("michael (at) kugele.net") also reported a way
to still be able to use OpenVPN's multi-client mode with nat-traverse: As all instances of
nat-traverse have to use unique ports (because a connection is identified by the
source/destination port combination), you've to use redirection rules to redirect the
ports used by nat-traverse to the port the OpenVPN daemon listens on:

iptables -t nat -A PREROUTING -p udp \
--dport $LPORT -j DNAT --to $HOST:$PORT
iptables -t nat -A PREROUTING -p udp \
--dport $PORT -j REDIRECT --to-port $LPORT

$LPORT specifies the source port nat-traverse uses on the server side, and "$HOST:$PORT"
is the address of the OpenVPN server.)

LIMITATIONS

Only IPv4 is supported, nat-traverse won't work with IPv6 addresses. Drop me a note if you
do need IPv6 support.

nat-traverse does not work with gateways which change the port numbers. This is a
fundamental problem of nat-traverse's design, as the changed port numbers are (in general)
not predictable.

Use nat-traverse online using onworks.net services