rigmem - Online in the Cloud

PROGRAM:

NAME

rigmem - backup and restore memory of radio transceivers and receivers

SYNOPSIS

rigmem [OPTION]... [COMMAND]...

DESCRIPTION

Backup and restore memory of radio transceivers and receivers. rigmem accepts commands
from the command line only.

Keep in mind that Hamlib is BETA level software. While a lot of backend libraries lack
complete rig support, the basic functions are usually well supported. The API may change
without publicized notice, while an advancement of the minor version (e.g. 1.1.x to 1.2.x)
indicates such a change.

Please report bugs and provide feedback at the e-mail address given in the REPORTING BUGS
section. Patches and code enhancements are also welcome.

OPTIONS

This program follows the usual GNU command line syntax, with long options starting with
two dashes (`-').

Here is a summary of the supported options:

-m, --model=id
Select radio model number. See model list (use 'rigctl -l').
NB: rigmem (or third party software) will use rig model 1901 when using rpc.rigd.

-r, --rig-file=device
Use device as the file name of the port the radio is connected. Often a serial
port, but could be a USB to serial adapter. Typically /dev/ttyS0, /dev/ttyS1,
/dev/ttyUSB0, etc.

-s, --serial-speed=baud
Set serial speed to baud rate. Uses maximum serial speed from rig backend
capabilities as the default.

-c, --civaddr=id
Use id as the CI-V address to communicate with the rig. Only useful for Icom rigs.
NB: the id is in decimal notation, unless prefixed by 0x, in which case it is
hexadecimal.

-C, --set-conf=parm=val[,parm=val]*
Set config parameter. e.g. stop_bits=2
Use -L option of rigctl for a list.

-x, --xml
Use XML format instead of CSV, if libxml2 is available.

-v, --verbose
Set verbose mode, cumulative (see DIAGNOSTICS below).

-h, --help
Show a summary of these options and exit.

-V, --version
Show version of rigmem and exit.

NOTE! Some options may not be implemented by a given backend and will return an error.
This is most likely to occur with the --set-conf option.

COMMANDS

Backup and restore are supported for basic CSV file and XML format where available.

Please note that the backend for the radio to be controlled, or the radio itself may not
support some commands. In that case, the operation will fail with a Hamlib error message.

Here is a summary of the supported commands:

save Save all the content of memory in a CSV (or XML) file given as an argument to the
command.

load Load the content into all the memory from a CSV (or XML) file given as an argument
to the command.

save_parm
Save all the parameters of the radio in a CSV (or XML) file given as an argument to
the command.

load_parm
Load the parameters of the radio from a CSV (or XML) file given as an argument to
the command.

clear This is a very DANGEROUS command, as it will completely clear out everything you
have programmed in the memory of your radio. ALL DATA WILL BE LOST. Use at your own
risk!

DIAGNOSTICS

The -v, --version option allows different levels of diagnostics to be output to stderr and
correspond to -v for BUG, -vv for ERR, -vvv for WARN, -vvvv for VERBOSE, or -vvvvv for
TRACE.

A given verbose level is useful for providing needed debugging information to the email
address below. For example, TRACE output shows all of the values sent to and received
from the radio which is very useful for radio backend library development and may be
requested by the developers.

EXIT STATUS

rigmem exits with:
0 if all operations completed normally;
1 if there was an invalid command line option or argument;
2 if an error was returned by Hamlib.
3 the Hamlib backend has no memory support implemented and/or
the rig has no memory access available.

Use rigmem online using onworks.net services