rs6 - Online in the Cloud

PROGRAM:

NAME

rs6 - A security assessment tool for attack vectors based on ICMPv6 Router Solicitation
messages

SYNOPSIS

rs6 [-i INTERFACE] [-s SRC_ADDR[/LEN]] [-d DST_ADDR] [-y FRAG_SIZE] [-u DST_OPT_HDR_SIZE]
[-U DST_OPT_U_HDR_SIZE] [-H HBH_OPT_HDR_SIZE] [-S LINK_SRC_ADDR] [-D LINK-DST-ADDR] [-E
LINK_ADDR] [-e] [-F N_SOURCES] [-z SECONDS] [-l] [-v] [-h]

DESCRIPTION

rs6 allows the assessment of IPv6 implementations with respect to a variety of attacks
based on ICMPv6 Router Solicitation messages. This tool is part of the SI6 Networks' IPv6
Toolkit: a security assessment suite for the IPv6 protocols.

OPTIONS

rs6 takes its parameters as command-line options. Each of the options can be specified
with a short name (one character preceded with the hyphen character, as e.g. "-i") or with
a long name (a string preceded with two hyphen characters, as e.g. "--interface").

Depending on the amount of information (i.e., options and option data) to be conveyed into
the Router Solicitations, it may be necessary for rs6 to split that information into more
than one Router Solicitation. Also, when the rs6 tool is instructed to flood the victim
with Router Solicitations from different sources ("--flood-sources" option), multiple
packets may need to be generated. rs6 supports IPv6 fragmentation, which may be of use if
a large amount of information needs to be conveyed within a single Router Solicitation
message. IPv6 fragmentation is not enabled by default, and must be explicitly enabled with
the "-y" option.

-i INTERFACE, --interface INTERFACE
This option specifies the network interface that the tool will use. If the
destination address ("-d" option) is a link-local address, the interface must be
explicitly specified. The interface may also be specified along with a destination
address, with the "-d" option.

-s SRC_ADDR, --src-address SRC_ADDR

This option is meant to specify the IPv6 Source Address (or IPv6 prefix) to be used
for the Router Solicitation messages. If left unspecified, a randomized link-local
unicast (fe80::/64) address is selected.

-d DST_ADDR, --dst-address DST_ADDR

This option specifies the IPv6 Destination Address of the Router Solicitation
messages. If left unspecified, but the Ethernet Destination Address is specified,
the "all-routers link-local multicast" address (ff02::2) is selected as the IPv6
Destination Address.

--hop-limit, -A

This option specifies the IPv6 Hop Limit to be used for the Router Solicitation
messages. It defaults to 255. Note that IPv6 nodes are required to check that the
Hop Limit of incoming Router Solicitation messages is 255. Therefore, this option
is only useful to assess whether an IPv6 implementation fails to enforce the
aforementioned check.

-y SIZE, --frag-hdr SIZE

This option specifies that the resulting packet must be fragmented. The fragment
size must be specified as an argument to this option.

-u HDR_SIZE, --dst-opt-hdr HDR_SIZE

This option specifies that a Destination Options header is to be included in the
resulting packet. The extension header size must be specified as an argument to
this option (the header is filled with padding options). Multiple Destination
Options headers may be specified by means of multiple "-u" options.

-U HDR_SIZE, --dst-opt-u-hdr HDR_SIZE

This option specifies a Destination Options header to be included in the
"unfragmentable part" of the resulting packet. The header size must be specified as
an argument to this option (the header is filled with padding options). Multiple
Destination Options headers may be specified by means of multiple "-U" options.
This option is only valid if the "-y" option is specified (as the concept of
"unfragmentable part" only makes sense when fragmentation is employed).

-H HDR_SIZE, --hbh-opt-hdr HDR_SIZE

This option specifies that a Hop-by-Hop Options header is to be included in the
resulting packet. The header size must be specified as an argument to this option
(the header is filled with padding options). Multiple Hop-by-Hop Options headers
may be specified by means of multiple "-H" options.

-S SRC_LINK_ADDR, --src-link-address SRC_LINK_ADDR

This option specifies the link-layer Source Address of the Router Solicitation
messages (currently, only Ethernet is supported). If left unspecified, the link-
layer Source Address is randomized.

-D DST_LINK_ADDR, --dst-link-address DST_LINK_ADDR

This option specifies the link-layer Destination Address of the Router Solicitation
messages (currently, only Ethernet is supported). If left unspecified, the link-
layer Destination Address is set to "33:33:00:00:00:02" (the Ethernet address that
corresponds to the "all-routers link-local multicast" address).

--source-lla-opt, -E

This option specifies the contents of a source link-layer address option to be
included in the Router Solicitation messages. If more than one source link-layer
address is specified (by means of multiple "-E" options), and all the resulting
options cannot be conveyed into a single Router Solicitation, multiple Router
Solicitations will be sent as needed.

--add-slla-opt, -e

This option instructs the rs6 tool to include a source link-layer address option in
the Router Solicitation messages that it sends. The link-layer address included in
the option is the same as the Ethernet Source Address used for the outgoing Router
Solicitation messages.

--flood-sources, -F

This option instructs the rs6 tool to send Router Solicitations from multiple (and
random) IPv6 Source Addresses. The number of different sources is specified as "-F
number". The IPv6 Source Address of each Router Solicitation is a randomized from
the IPv6 prefix specified with the "-s" option, and defaults to a random link-local
unicast address (fe80::/64).

--loop, -l

This option instructs the rs6 tool to send periodic Router Solicitations to the
destination node. The amount of time to pause between sending Neighbor
Solicitations can be specified by means of the "-z" option, and defaults to 1
second.

--sleep, -z

This option instructs the rs6 tool to the amount of time to pause between sending
Router Solicitation messages. If left unspecified, it defaults to 1 second.

--verbose, -v

This option instructs the rs6 tool to be verbose.

--help, -h

Print help information for the rs6 tool.

EXAMPLES

The following sections illustrate typical use cases of the rs6 tool.

Example #1

# rs6 -i eth0 -e

Use the network interface "eth0" to send a Router Solicitation using a random link-local
unicast IPv6 Source Address and a random Ethernet Source Address, to the IPv6 Destination
Address "ff02::2" ("all-routers link-local multicast" address, selected by default) and
the Ethernet Destination Address "33:33:00:00:00:02" (selected by default). The Router
Solicitation also includes a source link-layer address option, that contains the same
Ethernet address as that used for the Ethernet Source Address of the packet.

Example #2

# rs6 -i eth0 -e -F 100 -l -z 10 -v

Send 100 Router Solicitation messages using a random Ethernet Source Address and random
IPv6 Source Address for each of them, to the Ethernet Destination Address
"33:33:00:00:00:02" (default) and the IPv6 Destination Address "ff02:2" (default). Each
message includes a source link-layer address option that contains the same link-layer
address as that used for the Ethernet Source Address of the packet. Repeat this operation
every ten seconds. Be verbose.

Example #3

# rs6 -i eth0 -d fe80::1 -E ff:ff:ff:ff:ff:ff -v

Send one Router Solicitation message using a random Ethernet Source Address and a random
link-local unicast (i.e., fe80::/64) IPv6 Source Address, to the Ethernet Destination
Address "33:33:00:00:00:02" (default) and the IPv6 Destination Address "fe80::1". Each
Router Solicitation includes a source link-layer address option that contains the Ethernet
address "ff:ff:ff:ff:ff:ff". Be verbose.

Use rs6 online using onworks.net services